Datasheet.kr   

XX1001-QK 데이터시트 PDF




Mimix Broadband에서 제조한 전자 부품 XX1001-QK은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 XX1001-QK 자료 제공

부품번호 XX1001-QK 기능
기능 Doubler and Power Amplifier
제조업체 Mimix Broadband
로고 Mimix Broadband 로고


XX1001-QK 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 5 페이지수

미리보기를 사용할 수 없습니다

XX1001-QK 데이터시트, 핀배열, 회로
18.0-21.0/36.0-42.0 GHz Doubler and
Power Amplifier, QFN, 7x7mm
October 2006 - Rev 04-Oct-06
Features
Integrated Doubler and Power Amplifier
Excellent Saturated Output Stage
+25.0 dBm Output Power
50.0 dBc Fundamental Suppression
X1001-QK
General Description
Mimix Broadband's 18.0-21.0/36.0-42.0 GHz GaAs
doubler integrates a doubler, a buffer amplifier and
4-stage power amplifier.The device provides
better than +25.0 dBm output power and has
excellent fundamental rejection. The device
comes in a 7x7mm QFN package that is RoHS
compliant.This device is well suited for
Millimeter-wave Point-to-Point Radio, LMDS,
SATCOM and VSAT applications.
Absolute Maximum Ratings
Supply Voltage (Vd)
+6.0 VDC
Supply Current (Id)
800 mA
Gate Bias Voltage (Vg)
+0.3 VDC
Input Power (RF Pin)
TBD
Storage Temperature (Tstg) -65 to +165 OC
Operating Temperature (Ta) -55 to MTTF Table1
Channel Temperature (Tch) MTTF Table1
(1) Channel temperature affects a device's MTTF. It is
recommended to keep channel temperature as low as
possible for maximum life.
o
Electrical Characteristics (Ambient Temperature T = 25 C)
Parameter
Units Min. Typ. Max.
Input Frequency Range (fin)
GHz 18.0 - 21.0
Output Frequency Range (fout)
GHz 36.0 - 42.0
Input Return Loss (S11)
dB - TBD -
Output Return Loss (S22)
dB - 12.0 -
Fundamental Rejection
dBc - 50.0 -
RF Input Power (RF Pin)
dBm - 0.0 -
Output Power at 0.0 dBm Pin (Pout)
dBm - +26.0 -
Drain Supply Voltage (Vd1) Doubler
V - 2.5 3.0
Drain Supply Voltage (Vd2) Buffer Amp
V - 3.0 4.0
Drain Supply Voltage (Vd3,4,5,6) PA
V - 4.5 5.5
Gate Supply Voltage (Vg1) Doubler
V - -1.2 -
Drain Supply Current (Id1) Doubler
mA - <1.0 -
Drain Supply Current (Id2) Buffer
mA - 20 25
Drain Supply Current (Id3,4,5,6) (Vg=-0.7V Typical) PA
mA
-
530 600
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 1 of 5
Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.




XX1001-QK pdf, 반도체, 판매, 대치품
18.0-21.0/36.0-42.0 GHz Doubler and
Power Amplifier, QFN, 7x7mm
October 2006 - Rev 04-Oct-06
Recommended Layout
X1001-QK
App Note [1] Biasing - It is recommended to separately bias each amplifier stage Vd1 through Vd6 at Vd1=2.5V, Vd2=3.0V, Vd(3,4,5,6)=4.5V with
Id1<1mA, Id2=20mA, Id3=40mA, Id4=70mA, Id5=150mA, Id6=270mA. Separate biasing is recommended if the amplifier is to be used at high levels
of saturation, where gate rectification will alter the effective gate control voltage. As shown in the bonding diagram, it is possible to parallel stages
Vd(3,4,5) with Id(3,4,5)=260mA while maintaining satisfactory performance. For non-critical applications it is possible to parallel stages Vd(3,4,5,6)
together and adjust the common gate voltage Vg(3,4,5,6) for total drain current Id(total)=530mA. It is also recommended to use active biasing to
keep the currents constant as the RF power and temperature vary; this gives the most reproducible results. Depending on the supply voltage
available and the power dissipation constraints, the bias circuit may be a single transistor or a low power operational amplifier, with a low value
resistor in series with the drain supply used to sense the current.The gate of the pHEMT is controlled to maintain correct drain current and thus
drain voltage. The typical gate voltage needed to do this is -0.7V.Typically the gate is protected with Silicon diodes to limit the applied voltage. Also,
make sure to sequence the applied voltage to ensure negative gate bias is available before applying the positive drain supply.
MTTF Tables
MTTF is calculated from accelerated life-time data of single devices and assumes an isothermal back-plate.
1.0E+05
XX1001-QK, MTTF (yrs) vs. Backplate Temperature (°C)
1.0E+04
1.0E+03
1.0E+02
1.0E+01
1.0E+00
55
65 75 85
Temperature (°C)
95
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 4 of 5
Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.

4페이지












구       성 총 5 페이지수
다운로드[ XX1001-QK.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
XX1001-QK

Doubler and Power Amplifier

Mimix Broadband
Mimix Broadband

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵