|
|
PDF CMX867A Data sheet ( Hoja de datos )
| Número de pieza | CMX867A | |
| Descripción | Low Power V.22 Modem | |
| Fabricantes | CML Microcircuits | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CMX867A (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
CML Microcircuits
COMMUNICATION SEMICONDUCTORS
CMX867A
Low Power
V.22 Modem
D/867A/2 September 2006
Features
• V.22, Bell 212A 1200/1200 or 600/600 bps DPSK
• V.23 1200/75, 1200/1200, 75, 1200 bps FSK
• Bell 202 1200/150, 1200/1200, 150, 1200 bps FSK
• V.21 or Bell 103 300/300 bps FSK
• DTMF/Tones Transmit and Receive
• ‘Powersave’ Standby Mode
• Software and Hardware Compatible with CMX868A
Provisional Issue
Applications
• Telephone Telemetry Systems
• Remote Utility Meter Reading
• Security Systems
• Industrial Control Systems
• Electronic Cash Terminals
• Pay-Phones
• Set-Top Boxes
1. Brief Description
The CMX867A is a multi-standard modem for use in telephone based information and telemetry systems.
Control of the device is via a simple high speed serial bus, compatible with most types of µC serial
interface. The data transmitted and received by the modem is also transferred over the same serial bus.
On-chip programmable Tx and Rx USARTs meeting the requirements of V.14 are provided for use with
asynchronous data and allow unformatted synchronous data to be received or transmitted as 8-bit words.
A high-quality DTMF decoder with excellent immunity to falsing on voice and a standard DTMF encoder
are included. Alternatively, these blocks can be used to transmit and detect user-specific, programmed
single and dual-tone signals, call progress signals or modem calling and answering tones.
Flexible line driver and receive hybrid circuits are integrated on chip, requiring only passive external
components to build a 2 or 4-wire line interface.
The device also features a Hook Switch Relay Drive output and a Ring Detector circuit which continues to
function when the device is in the Powersave mode, providing an interrupt which can be used to wake up
the host µController when line voltage reversal or ringing is detected.
The CMX867A operates from a single 2.7 to 5.5V supply over a temperature range of -40°C to +85°C and
is available in 24-pin TSSOP, SOIC and DIP packages.
© 2006 Consumer Microcircuits Limited
1 page  
Low Power V.22 Modem
Notes:
I/P
O/P
BI
T/S
NC
=
=
=
=
=
Input
Output
Bidirectional
3-state Output
No Connection
4. External Components
CMX867A
R1 100kΩ
X1 11.0592MHz
or 12.288MHz
C1, C2
C3, C4
C5
22pF
100nF
10uF
Resistors ±5%, capacitors ±20% unless otherwise stated.
Figure 2 Recommended External Components for a Typical Application
This device is capable of detecting and decoding small amplitude signals. To achieve this VDD and VBIAS
should be decoupled and the receive path protected from extraneous in-band signals. It is recommended
that the printed circuit board is laid out with a VSS ground plane in the CMX867A area to provide a low
impedance connection between the VSS pins and the VDD and VBIAS decoupling capacitors. The VSS
connections to the Xtal oscillator capacitors C1 and C2 should also be low impedance and preferably be
part of the VSS ground plane to ensure reliable start up of the oscillator.
For best results, an Xtal oscillator design should drive the clock inverter input with signal levels of at least
40% of VDD peak-to-peak. Tuning-fork Xtals generally cannot meet this requirement. To obtain Xtal
oscillator design assistance, please consult your Xtal manufacturer.
© 2006 Consumer Microcircuits Limited
5
D/867A/2
5 Page 
Low Power V.22 Modem
CMX867A
5.1 Tx USART
A flexible Tx USART is provided for all modem modes, meeting the requirements of V.14 for DPSK
modems.
It can be programmed to transmit continuous patterns, Start-Stop characters or Synchronous Data.
In both Synchronous Data and Start-Stop modes the data to be transmitted is written by the µC into the 8-
bit C-BUS Tx Data Register from which it is transferred to the Tx Data Buffer.
If Synchronous Data mode has been selected the 8 data bits in the Tx Data Buffer are transmitted serially,
b0 being sent first.
In Start-Stop mode a single Start bit is transmitted, followed by 5, 6, 7 or 8 data bits from the Tx Data
Buffer - b0 first - followed by an optional Parity bit then - normally - one or two Stop bits. The Start, Parity
and Stop bits are generated by the USART as determined by the Tx Mode Register settings and are not
taken from the Tx Data Register.
Figure 5a Tx USART
Every time the contents of the C-BUS Tx Data Register are transferred to the Tx Data Buffer the Tx Data
Ready flag bit of the Status Register is set to 1 to indicate that a new value should be loaded into the C-
BUS Tx Data Register. This flag bit is cleared to 0 when a new value is loaded into the Tx Data Register.
Figure 5b Tx USART Function (Start-Stop mode, 8 Data Bits + Parity)
If a new value is not loaded into the Tx Data Register in time for the next Tx Data Register to Tx Data
Buffer transfer then the Status Register Tx Data Underflow bit will be set to 1. In this event the contents of
the Tx Data Buffer will be re-transmitted if Synchronous Data mode has been selected, or if the Tx
modem is in Start-Stop mode then a continuous Stop signal (1) will be transmitted until a new value is
loaded into the Tx Data Register.
© 2006 Consumer Microcircuits Limited
11
D/867A/2
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet CMX867A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CMX867 | Low Power V.22 Modem | CML Microcircuits |
| CMX867A | Low Power V.22 Modem | CML Microcircuits |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |