Datasheet.kr   

TSOP37356 데이터시트 PDF




Vishay에서 제조한 전자 부품 TSOP37356은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 TSOP37356 자료 제공

부품번호 TSOP37356 기능
기능 IR Receiver Modules
제조업체 Vishay
로고 Vishay 로고


TSOP37356 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 11 페이지수

미리보기를 사용할 수 없습니다

TSOP37356 데이터시트, 핀배열, 회로
www.vishay.com
TSOP373.., TSOP375..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
22531-1
ORDERING CODE
Taping:
TSOP37...TT - top view taped
TSOP37...TR - side view taped
FEATURES
• Very low supply current
• Photo detectors and preamplifier in one package
• Internal filter for PCM frequency
• Supply voltage: 2.5 V to 5.5 V
• Improved immunity against ambient light
• Insensitive to supply voltage ripple and noise
• Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912
DESCRIPTION
The TSOP373.., TSOP375.. series are miniaturized receiver
modules for infrared remote control systems. A PIN diode
and a preamplifier are assembled on a PCB, the epoxy
package contains an IR filter. The demodulated output
signal can be directly connected to a microprocessor for
decoding.
The TSOP373.. series devices are optimized to suppress
almost all spurious pulses from energy saving lamps like
CFLs. AGC3 may also suppress some data signals if
continuously transmitted.
New designs should prefer the TSOP373.. series containing
the newer AGC3. The TSOP375.. series contain a very
robust AGC5. This series should only be used for critically
noisy environments.
These components have not been qualified according to
automotive specifications.
PARTS TABLE
AGC
36 kHz
Carrier
38 kHz
frequency 40 kHz
56 kHz
Package
Pinning
Dimensions (mm)
Mounting
Application
Best remote control code
NOISY ENVIRONMENTS
AND SHORT BURSTS (AGC3)
VERY NOISY ENVIRONMENTS
AND SHORT BURSTS (AGC5)
TSOP37336 (1)
TSOP37536
TSOP37338 (2)(3)(4)(5)
TSOP37538
TSOP37340
TSOP37540
TSOP37356
TSOP37556
Belobog
1 = OUT, 2, 3, 6, 7, 8 = GND, 4, 5 = VS
3.95 W x 3.95 H x 0.8 D
SMD
Remote control
(1) MCIR (2) Mitsubishi (3) RECS-80 Code (4) r-map (5) XMP-1, XMP-2
Rev. 1.6, 10-Nov-15
1 Document Number: 82446
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000




TSOP37356 pdf, 반도체, 판매, 대치품
www.vishay.com
1.0
f = 100 Hz
0.9
0.8
f = 10 kHz
0.7
0.6
f = 20 kHz
0.5
0.4
f = 30 kHz
0.3
0.2 f = fo
0.1
20753
0
1 10 100 1000
VsRMS - AC Voltage on DC Supply Voltage (mV)
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
1
0.9
0.8 f = 38 kHz, Ee = 2 mW/m²
0.7
0.6
0.5
0.4
0.3
0.2 TSOP373..
0.1
0
0
TSOP375..
20 40 60 80 100 120
Burst Length (number of cycles/burst)
Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length
0.30
0.25
0.20
0.15
0.10
0.05
0
-30 -10 10 30 50 70 90
Tamb - Ambient Temperature (°C)
Fig. 9 - Sensitivity vs. Ambient Temperature
TSOP373.., TSOP375..
Vishay Semiconductors
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
750 800 850 900 950 1000 1050 1100 1150
λ - Wavelength (nm)
Fig. 10 - Relative Spectral Sensitivity vs. Wavelength
-20° -10° 0° 10° 20°
-30° 30°
-40° 40°
-50° 50°
-60° 60°
-70° 70°
-80° 80°
21947
0.1 0.3 0.5 0.7 0.9
Fig. 11 - Directivity
0.30
0.25
0.20
0.15
0.10
0.05
0.00
1
234
VS - Supply Voltage (V)
5
Fig. 12 - Sensitivity vs. Supply Voltage
Rev. 1.6, 10-Nov-15
4 Document Number: 82446
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

4페이지










TSOP37356 전자부품, 판매, 대치품
www.vishay.com
TSOP373.., TSOP375..
Vishay Semiconductors
ASSEMBLY INSTRUCTIONS
Reflow Soldering
• Reflow soldering must be done within 168 h while stored
under a max. temperature of 30 °C, 60 % RH after
opening the dry pack envelope
• Set the furnace temperatures for pre-heating and heating
in accordance with the reflow temperature profile as
shown in the diagram. Exercise extreme care to keep the
maximum temperature below 260 °C. The temperature
shown in the profile means the temperature at the device
surface. Since there is a temperature difference between
the component and the circuit board, it should be verified
that the temperature of the device is accurately being
measured
• Handling after reflow should be done only after the work
surface has been cooled off
Manual Soldering
• Use a soldering iron of 25 W or less. Adjust the
temperature of the soldering iron below 300 °C
• Finish soldering within 3 s
• Handle products only after the temperature has cooled off
VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE
300
250
255 °C
240 °C
217 °C
200
150
max. 120 s
100
max. 260 °C
245 °C
max. 20 s
max. 100 s
50 max. Ramp Up 3 °C/s max. Ramp Down 6 °C/s
0
0
19800
50 100 150 200 250 300
t (s) max. 2 cycles allowed
ORDERING INFORMATION
ORDERING CODE
TSOP37..TT1
TSOP37..TT2
Note
(1) MOQ: minimum order quantity
PACKAGING
Tape and reel
VOLUME (1)
MOQ: 1800 pcs
MOQ: 7000 pcs
REMARKS
3.95 mm x 3.95 mm x 0.75 mm
Rev. 1.6, 10-Nov-15
7 Document Number: 82446
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

7페이지


구       성 총 11 페이지수
다운로드[ TSOP37356.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
TSOP37356

IR Receiver Modules

Vishay
Vishay

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵