|
|
Número de pieza | LC5710S | |
Descripción | power IC for LED driver | |
Fabricantes | SANKEN | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de LC5710S (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! LC5710S DATA SHEET
LC5710S
DATA SHEET Rev.1.9
Rev.1.9
SANKEN ELECTRIC CO., LTD.
http://www.sanken-ele.co.jp
Copy Right: SANKEN ELECTRIC CO., LTD.
Page.1
1 page LC5710S DATA SHEET
Rev.1.9
3.Electrical Characteristics
Certain details refer to the specification sheet of this product.
The polarity value for current specifies a sink as “+” and a source as “−”, referencing the IC.
3.1 Electrical Characteristics of Control Part (MIC) Unless specifically noted, Ta is 25°C, VIN=15V
Table.3
Parameter
Terminal Symbol
Ratings
Units
MIN TYP MAX
Remarks
O p e r a t i o n S t a r t V o l t a g e 5−3 VIN(ON) 3.8 4.1 4.5 V
Operation Stop Voltage
5−3 VIN(OFF) 3.4 3.7 4.2 V
Operation Hysteresis Voltage
5−3 VIN(HYS) 0.25 0.37 0.50
V
Supply Current
(6) 5−3
IIN(ON)
―
1.6
― mA
Supply Current in No Operation (6) 5−3
IIN(OFF)
―
0.24
―
mA VIN= 3V
Oscillator Frequency1
― fOSC1 80 100 135 kHz RRT=180kΩ
Oscillator Frequency2
― fOSC2 350 500 650 kHz RRT=18kΩ
Minimum On Time
Maximum Duty Cycle
Current Sense Voltage
―
tON(MIN)
100
200
300
ns VCOMP= 0V
― DMAX 84
90
95
%
VCOMP= 2.8
V
6−7 VCS
97 100 103 mV
SW Current Limit
4−3
ISW(LIM)
1.4
1.8
2.2
A
CSP Input Current
6−3 ICSP 22 35 50 µA
CSN Input Current
7−3 ICSN
5 9.5 18 µA
COMP Terminal Source Current
1−3 ICOMP(SO) -65
-50
-35
µA
VCS=20mV
VCOMP=2V
COMP Terminal Sink Current
1−3
ICOMP(SI)
35
50
65
µA
VCS=180mV
VCOMP=2V
Error Amplifier Conductance
(6) ―
GM
―
4.2
―
mS
VCS=70
~130mV
Over Voltage Threshold
6−7 VCS(OVP) 140 150 160 mV
Setup time of Watch Dog Timer (6) ―
TWDT
―
30
―
mS
Vcomp=2.5V
Vcs=short
DIM Voltage in LED On at
Dimming mode
8−3 VDIM(ON) 0.17 0.20 0.23
V
DIM Voltage in LED Off at
Dimming mode
8−3 VDIM(OFF) 0.12 0.15 0.18
V
DIM Hysteresis Voltage at
Dimming mode
8−3 VDIM(HYS)
10
50 100 mV
Thermal Shutdown
(6) ―
TSD
― 165 ― °C
Thermal Shutdown Hysteresis (6) ― TSD(HYS) ― 22 ― °C
(6) Guaranteed by design, not tested.
Copy Right: SANKEN ELECTRIC CO., LTD.
Page.5
5 Page LC5710S DATA SHEET
Rev.1.9
LED string current is detected by the current detection resistor, RCS.
The voltage of RCS is detected by both CSP and CSN pins. This IC compares this voltage with the Current Detection
Voltage, VCS, and makes a target value for current control.
The constant current is controlled so that the detection voltage of peak current of internal power MOSFET is close to
the target value, and thus the LED string current is constant.
The constant current of LED string, IOUT, is calculated by the following with RCS as the current detection resistor and
ROVP as the resistor for overvoltage protection in the case that LED string is open.
IOUT VCS ICSN (RCS ROVP)
RCS
・・・(2)
where; ICSN : the CSN Pin Sink Current, 9.5μA.
VCS : the Current Detection Voltage, 100mV.
Also, IOUT can be expressed by the following, if ICSN×(RCS+ROVP) is negligibly small against VCS.
IOUT VCS
RCS
・・・(3)
ROVP value should be chosen so that IOUT is within the acceptable accuracy range referring to the calculation in “8.5
Overvoltage Protection Function (OVP)”.
8.3 LED Dimming
8.3.1 Analog dimming
The dimming of LC5710S copes with both of Analog (the input of a DC voltage) and PWM-digital-Dimming.
Though it is Analog-dimming first, there are relations of the fig.8(A),(B) in the input DC voltage of the DIM pin and
the dimming-ratio. Moreover,Dimming by the Pull-down resistor RDIM is possible by using a internal current-source
of the IC, too. The relations of the DIM pin voltage and RDIM are shown by the figure 8 (B). Dimming ratio is 100%
when the DIM pin voltage is more than DC 2V.
fig.8(A) DIM Pin voltage vs. LED Current
fig.8(B) Pull-down resistor RDIM vs. DIM pin voltage
Though LC5710S doesn't have an exclusive
"Remote ON/OFF pin",
But,"Remote ON/OFF function" is as well as
possible by using a DIM pin.
fig.8I The connection of RDIM and remote ON/OFF application
From the port of the microcomputer of the use and so on, and if the DIM pin of LC5710S is held continuously to
the “Low” level,LC5710S continues suspension of a movement. The “Low level” voltage must be lower voltage
than VDIM (OFF). For reverse logic, put one small signal Transistor as the fig8I.
Copy Right: SANKEN ELECTRIC CO., LTD.
Page.11
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet LC5710S.PDF ] |
Número de pieza | Descripción | Fabricantes |
LC5710S | power IC for LED driver | SANKEN |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |