|
|
PDF MAX8650 Data sheet ( Hoja de datos )
| Número de pieza | MAX8650 | |
| Descripción | 4.5V to 28V Input Current-Mode Step-Down Controller | |
| Fabricantes | Maxim Integrated Products | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MAX8650 (archivo pdf) en la parte inferior de esta página. Total 25 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
19-3973; Rev 0; 1/06
EVAALVUAAILTAIOBNLEKIT 4.5V to 28V Input Current-Mode Step-
Down Controller with Adjustable Frequency
General Description
The MAX8650 synchronous PWM buck controller oper-
ates from a 4.5V to 28V input and generates an
adjustable 0.7V to 5.5V output voltage at loads up to 25A.
The MAX8650 uses a peak current-mode control archi-
tecture with an adjustable (200kHz to 1.2MHz) constant
switching frequency and is externally synchronizable. The
IC’s current limit uses the inductor’s DC resistance to
improve efficiency or an external sense resistor for high
accuracy. The current-limit threshold is adjusted with an
external resistor. Foldback-type current limit can be
implemented to reduce the power dissipation in overload
or short-circuit conditions. Short-circuit protection is
provided based on sensing the current in the low-side
MOSFET. A reference input is provided for use with a
high-accuracy external reference or for double-data-rate
(DDR)-tracking applications.
Monotonic prebiased startup is available for a safe-start
in applications where the output capacitor may have an
initial charge. This feature prevents the output from
pulling low during startup, which is a common charac-
teristic of conventional buck regulators.
A 180° out-of–phase synchronization output is available
for synchronizing with another converter.
Applications
Base Stations
DDR
Network and Telecom Power Modules
Storage
IBA Applications
Servers
Pin Configuration appears at end of data sheet.
Features
♦ Operates from 4.5V to 28V Supply
♦ 1% FB Voltage Accuracy Over Temperature
♦ Adjustable Output Voltage Down to 0.7V or REFIN
♦ Adjustable Switching Frequency or External
Synchronization from 200kHz to 1.2MHz
♦ 180° Phase-Shifted Clock Output
♦ Adjustable Overcurrent Limit
♦ Adjustable Foldback Current Limit
♦ Adjustable Slope Compensation
♦ Selectable Current-Limit Mode: Latch-Off or
Automatic Recovery
♦ Monotonic Output-Voltage Rise at Startup
♦ Output Sources and Sinks Current
♦ Enable Input
♦ Power-OK (POK) Output
♦ Adjustable Soft-Start
♦ Independently Adjustable Overvoltage Protection
Ordering Information
PART
MAX8650EEG+
TEMP RANGE
-40°C to +85°C
PIN-PACKAGE
PKG
CODE
24 QSOP
E24-1
+Denotes lead-free package.
Typical Operating Circuit
R1
SYNC
ON EN
OFF
POK
SYNCO
R2
R3
C3
R4
C4 R5
R6
R7
1
FSYNC
11
EN
24
POK
3
SYNCO
23
SCOMP
22
ILIM2
21
REFIN
20
SS
MAX8650EEG
16
ILIM1
19
COMP
18
FB
17
OVP
2
MODE
4
BST
5
DH
6
LX
DL 7
D2
C2
8
PGND
VL 9
10
IN
12
AVL
C7
C8
C10
14
CS+
15
CS-
13
GND
C11
Q1
Q2
VIN
7V TO 28V
C1
L1
R8
C6
R9
VOUT
0.7V TO 5.5V
C5
C9
________________________________________________________________ Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1 page  
4.5V to 28V Input Current-Mode Step-Down
Controller with Adjustable Frequency
ELECTRICAL CHARACTERISTICS (continued)
(VIN = 12V, VBST - VLX = 6.5V, TA = -40°C to +85°C. Typical values are at TA = +25°C, unless otherwise noted.) (Note 1)
POK
PARAMETER
Power-OK Threshold
POK Output Voltage, Low
POK Leakage Current, High
OVP
OVP Threshold Voltage
CONDITIONS
MIN TYP MAX
REFIN = AVL, VFB rising, typical hysteresis is 3%
VREFIN = 0.7V to 1.5V, VFB rising, typical hysteresis is 3%
VFB = 0.6V, IPOK = 2mA
VPOK = 5.5V
629.0
88.7
650.0
91.7
25
671.0
94.7
200
1
REFIN = AVL
VREFIN = 0.7V to 1.5V
770 800 840
110 115 120
OVP Leakage Current, High
MODE CONTROL
MODE Logic-Level Low
MODE Logic-Level High
MODE Input Current
SHUTDOWN CONTROL
EN Logic-Level Low
EN Logic-Level High
EN Input Current
VOVP = 0.8V
4.5V ≤ VAVL ≤ 5.5V
4.5V ≤ VAVL ≤ 5.5V
VMODE = 0 to VAVL
4.5V ≤ VAVL ≤ 5.5V
4.5V ≤ VAVL ≤ 5.5V
VEN = 0V
VEN = 28V
500
0.4
1.8
-1 +1
0.45
2
-1 +1
1.5 6.0
UNITS
mV
% of
mV
µA
mV
% of
VREFIN
nA
V
V
µA
V
V
µA
Note 1: Specifications are 100% production tested at TA = +85°C. Limits over the operating temperature range are guaranteed
by design.
_______________________________________________________________________________________ 5
5 Page 
4.5V to 28V Input Current-Mode Step-Down
Controller with Adjustable Frequency
Detailed Description
DC-DC Converter Control Architecture
The MAX8650 step-down controller uses a PWM, cur-
rent-mode control scheme. An internal transconduc-
tance amplifier establishes an integrated error voltage.
The heart of the PWM controller is an open-loop com-
parator that compares the integrated voltage-feedback
signal against the amplified current-sense signal plus
the adjustable slope-compensation ramp, which are
summed into the main PWM comparator to preserve
inner-loop stability. At each rising edge of the internal
clock, the high-side MOSFET turns on until the PWM
comparator trips or the maximum duty cycle is
reached. During this on-time, current ramps up through
the inductor, storing energy in a magnetic field and
sourcing current to the output. The current-mode feed-
back system regulates the peak inductor current as a
function of the output-voltage error signal. The circuit
acts as a switch-mode transconductance amplifier and
pushes the output LC filter pole normally found in a
voltage-mode PWM to a higher frequency.
During the second half of the cycle, the high-side
MOSFET turns off and the low-side MOSFET turns on.
The inductor releases the stored energy as the current
ramps down, providing current to the output. The output
capacitor stores charge when the inductor current
exceeds the required load current and discharges when
the inductor current is lower, smoothing the voltage
across the load. Under soft-overload conditions, when
the peak inductor current exceeds the selected current
limit (see the Current-Limit Circuit section), the high-side
MOSFET is turned off immediately and the low-side
MOSFET is turned on and remains on to let the inductor
current ramp down until the next clock cycle. Under
heavy-overload or short-circuit conditions, the valley
foldback current limit is enabled to reduce power dissi-
pation of external components.
The MAX8650 operates in a forced-PWM mode. As a
result, the controller maintains a constant switching fre-
quency, regardless of load, to allow for easier filtering
of the switching noise.
Internal Linear Regulators
The MAX8650 contains two internal LDO regulators. The
AVL regulator provides 5V for the IC’s internal circuitry,
and the VL regulator provides 6.5V for the MOSFET gate
drivers. Connect a 4.7µF ceramic capacitor from VL to
PGND, and connect a 1µF ceramic capacitor from AVL
to GND. For applications where the input voltage is
between 4.5V and 7V, connect VL directly to IN and con-
nect a 10Ω resistor from VL to AVL.
Undervoltage Lockout
When AVL drops below 4.03V, the MAX8650 assumes
that the supply voltage is too low for proper operation,
so the undervoltage-lockout (UVLO) circuitry inhibits
switching and forces the DL and DH gate drivers low.
When AVL rises above 4.15V, the controller enters the
startup sequence and then resumes normal operation.
Startup and Soft-Start
The internal soft-start circuitry gradually ramps up the
reference voltage to control the rate of rise of the step-
down controller’s output and reduce input surge cur-
rents during startup. The soft-start period is determined
by the value of the capacitor from SS to GND. The soft-
start time is approximately (30.4ms/µF) x CSS. The
MAX8650 also features monotonic output-voltage rise;
therefore, both external power MOSFETs are kept off if
the voltage at FB is higher than the voltage at SS. This
allows the MAX8650 to start up into a prebiased output
without pulling the output voltage down.
Before the MAX8650 can begin the soft-start and power-
up sequence, the following conditions must be met:
• VAVL exceeds the 4.15V UVLO threshold.
• EN is at logic-high.
• The thermal limit is not exceeded.
Enable (EN)
The MAX8650 features a low-power shutdown mode. A
logic-low at EN shuts down the controller. During shut-
down, the output is high impedance, and both DH and
DL are low. Shutdown reduces the quiescent current
(IQ) to less than 10µA. A logic-high at EN enables the
controller.
Synchronous-Rectifier Driver (DL)
Synchronous rectification reduces conduction losses in
the rectifier by replacing the normal Schottky catch
diode with a low-resistance MOSFET switch. The
MAX8650 also uses the synchronous rectifier to ensure
proper startup of the boost gate-driver circuit and to
provide the current-limit signal. The low-side gate driver
(DL) swings from 0 to the 6.5V provided from VL. The
DL waveform is always the complement of the DH high-
side gate-drive waveform (with controlled dead time to
prevent cross-conduction or shoot-through). An adap-
tive dead-time circuit monitors the DL voltage and pre-
vents the high-side MOSFET from turning on until DL is
fully off. For the dead-time circuit to work properly,
there must be a low-resistance, low-inductance path
from the DL driver to the MOSFET gate. Otherwise,
the sense circuitry in the MAX8650 can interpret the
MOSFET gate as off when gate charge actually
remains. Use very short, wide traces, approximately 10
______________________________________________________________________________________ 11
11 Page | ||
| Páginas | Total 25 Páginas | |
| PDF Descargar | [ Datasheet MAX8650.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MAX865 | Compact / Dual-Output Charge Pump |  Maxim Integrated |
| MAX8650 | 4.5V to 28V Input Current-Mode Step-Down Controller | Maxim Integrated Products |
| MAX8654 | 8A 1.2MHz Step-Down Regulator | Maxim Integrated Products |
| MAX865EUA | Compact / Dual-Output Charge Pump | Maxim Integrated |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |