DataSheet.es    


PDF TMP86FH46NG Data sheet ( Hoja de datos )

Número de pieza TMP86FH46NG
Descripción 8-Bit Microcontroller
Fabricantes Toshiba Semiconductor 
Logotipo Toshiba Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de TMP86FH46NG (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! TMP86FH46NG Hoja de datos, Descripción, Manual

www.DataSheet4U.com

1 page




TMP86FH46NG pdf
TMP86FH46
Operation
This section describes the functions and basic operational blocks of TMP86FH46.
www.DataSheeTth4Ue.cTomMP86FH46 has flash memory in place of the mask ROM which is included in the
TMP86C846/H46. The configuration and function are the same as the TMP86C846/H46.
1. Operating Mode
The TMP86FH46 has MCU mode and serial PROM mode.
1.1 MCU Mode
The MCU mode is set by fixing the TEST pin to the low level.
In the MCU mode, the operation is the same as the TMP86C846/H46.
1.1.1
Program memory
The TMP86FH46 has a 16-Kbyte built-in flash memory (addresses C000H to FFFFH in the
MCU mode).
When using TMP86FH46 for evaluation of TMP86C846/H46, the program is written by the
serial PROM mode.
0000H
0000H
C000H
C000H
FFFFH
Program
TMP86CH46
FFFFH
Program
MCU mode
TMP86FH46
(a) ROM Size = 16 Kbytes
0000H
0000H
E000H
E000H
FFFFH
Program
TMP86C846
FFFFH
Program
MCU mode
TMP86FH46
(b) ROM Size = 8 Kbytes
Figure 1.1.1 Program Memory Area
Note: The area that is not in use should be set data to FFH.
86FH46-5
2007-08-07

5 Page





TMP86FH46NG arduino
TMP86FH46
2.6 Operation Mode
www.DataSheetT4Uh.ecroemare four operating modes in serial PROM mode: Flash memory writing mode, RAM loader
mode, flash memory SUM output mode and product discrimination code output mode. For details
about these modes, refer to (1) Flash memory writing mode through (4) Product discrimination code
output mode.
(1) Flash memory writing mode
The data are written to the specified flash memory addresses. The controller should send the
write data in the Intel Hex format (Binary). For details of writing data format, refer to 2.7
“Flash Memory Writing Data Format”.
If no errors are encountered till the end record, the SUM of 16 Kbytes of flash memory is
calculated and the result is returned to the controller.
To execute the flash memory writing mode, the TMP86FH46 checks the passwords except a
blank product. If the passwords did not match, the program is not executed.
(2) RAM loader mode
The RAM loader transfers the data into the internal RAM that has been sent from the
controller in Intel Hex format. When the transfer has terminated normally, the RAM loader
calculates the SUM and sends the result to the controller before it starts executing the user
program. After sending of SUM, the program jumps to the start address of RAM in which the
first transferred data has been written. This RAM loader function provides the user's own way
to control on-board programming.
To execute the RAM loader mode, the TMP86FH46 checks the passwords except a blank
product. If the passwords did not match, the program is not executed.
(3) Flash memory SUM output mode
The SUM of 16 Kbytes of flash memory is calculated and the result is returned to the
controller.
The BOOT ROM does not support the reading function of the flash memory. Instead, it has
this SUM command to use. By reading the SUM, it is possible to manage Revisions of
application programs.
(4) Product discrimination code output mode
The product discrimination code is output as a 13-byte data, that includes the start address
and the end address of ROM. (In case of TMP86FH46, the start address is C000H and the end
address is FFFFH.) Therefore, the controller can recognize the device information by using this
function.
86FH46-11
2007-08-07

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet TMP86FH46NG.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
TMP86FH46NCMOS 8-Bit MicrocontrollerToshiba Semiconductor
Toshiba Semiconductor
TMP86FH46NG8-Bit MicrocontrollerToshiba Semiconductor
Toshiba Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar